Cool water supply – Kenmore Coldspot 106 consumer handbook

Web Web Web Page 8

Read all instructions very very carefully before starting. ESSENTIAL;

If operating the fridge before setting up the water connection, turn ice maker towards the OFF position to stop procedure without water.

All installments should be relative to regional plumbing system

Use copper tubing and look for leaks.

Install copper tubing only in areas where conditions will stay above freezing.

If can take around a day for the ice manufacturer to start ice that is producing.

Tools needed;

in. open-end wrenches or two adjustable

Hand drill or drill that is electricprecisely grounded)

Your fridge dealer features a kit available having a

in. (6.35 mm) saddle-type shut-off valve, a union, and copper

tubing. Before buying, make certain a saddle-type valve

complies together with your neighborhood plumbing system codes. Don’t use a piercingВ­

in. (4.76 mm) seat valve which decreases water movement

and clogs more easily.

Cool water supply

The ice manufacturer water valve includes a movement washer that is utilized

as a water stress regulator. The ice manufacturer has to be linked to a water that is cold with water stress between 30 and 120 psi. In case a issue happens, phone your energy business.

Linking to water line:

1. Unplug ice box or disconnect energy.

Turn OFF main water supply. Switch on nearest tap very very very long

adequate to clear type of water.

water pipeline close to the fridge.

Horizontal pipeline is going to work, however the following procedure

needs to be followed: Drill from the top region of the pipeline, perhaps not the underside. This can help in keeping water away from the drill. And also this keeps normal sediment from gathering within the valve.

To look for the period of copper tubing you will need,

measure from connection on reduced rear that is left of to

water pipeline. Include 7 ft. (2.1 m) to accommodate going refrigerator for cleansing. utilize 14 in. (6.35 mm) O.D. (outside diameter)

copper tubing. Make sure both ends of copper tubing are cut square.

Employing a grounded drill, drill a 14 in. gap within the chilled water pipeline

you’ve got chosen.

1. Chilled Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

Fasten shut-off valve to cool water pipeline with pipeline clamp. Be

yes socket end is sturdily into the 14 in. drilled opening into the water

pipe and therefore washer is underneath the pipeline clamp. Tighten packing nut. Tighten the pipeline clamp screws very very carefully and

evenly so washer makes a watertight seal. Don’t overtighten or you may crush the copper tubing, particularly when soft (coiled) copper tubing can be used. Now you are prepared to link the copper tubing.

Slide compression nut on copper tubing as shown. Insert end of tubing into socket end squarely so far as it will go. Screw compression nut onto socket end with adjustable wrench. Try not to overtighten.

Put the end that is free of tubing into a container or sink, and

switch on water that is main and flush out tubing until water is obvious. Turn OFF shut-off valve regarding the water pipeline. Coil copper tubing.

Connecting to ice box:

1. Connect the copper pipe into the valve inlet using a compression

nut and sleeve as shown. Fasten the compression nut. Usually do not overtighten. Make use of the pipe clamp in the relative straight back regarding the

ice box to secure the tubing to your refrigerator as shown. This can help alleviate problems with injury to the tubing if the ice box is pressed right right straight back up against the wall surface. Move to step two.

2. Turn shut-off valve ON. Search for leakages.

connections (including connections during the valve) or pea pea pea nuts that

Copper Tubing

3. Compression Nut

4. Valve Inlet

The ice manufacturer comes with a integrated water strainer. If

regional water conditions need regular cleaning or perhaps a well is

your way to obtain water supply, a 2nd water strainer should

be set up into the

in. (6.35 mm) water line. Have a water

strainer from your own nearest appiiance dealer. Install at either pipe connection.

Napsat komentář

Vaše e-mailová adresa nebude zveřejněna. Vyžadované informace jsou označeny *